کنترل ال ای دی بلست کیبورد دار BLEST

1.Instructions for use

A side function operation instructions

1. RF and IR function switching

By default, the ST works in RF wireless mode when powered on, and the LED light is off. Press any button at this time, the LED light will flash once.

In the wireless working mode, when you press “” for about one second, the MX3 will switch to the infrared working mode, the LED light will be on at this time, and the LED will flash once when any key is pressed. In the infrared working mode, you can enter the infrared learning function.

In the infrared working mode, press “” for about one second, the MX3 will switch to the RF working mode, and the LED light will be off at this time

B-side wireless code value

1. By default, all buttons on the B side only send wireless code values, and the code values refer to the code table used by HID devices.

2. Press “” once to lock the uppercase function, press “” again, the uppercase function is released, and input lowercase.

3. Press “” once to lock the function of entering numbers and special characters, and press “” again to release the function of entering numbers and special characters.

Functional Operation Instructions

1. USB receiver

The ST USB receiver is defined as a standard HID device, plug and play, receives signals and data from the transmitter, and supports Windows, Android and iOS systems 1. 2. Pairing

2.1 Press and hold the “TV” button and “Ok” button on the A side at the same time when the power is turned on, then the LED flashes quickly and enters the wireless pairing mode.

2.2 Insert the USB receiver to power on and wait for about 3 seconds. If the LED on the A side of the MX3 stops flashing, it means the pairing is successful.

3. Air mouse cursor pointer speed adjustment

3.1 The speed of the cursor pointer is accelerated: press “OK” and “Vol+” at the same time, the LED light flashes rapidly for about 1 second, indicating that the speed of the cursor pointer increases by one level;

3.2 Cursor pointer speed slows down: Press “OK” and “Vol-” at the same time, the LED light flashes rapidly for about 1 second, indicating that the cursor pointer speed slows down by one level;

Note: There are about 12 speed adjustments in total. When the pointer speed is already at 12, it can only be adjusted slower or faster.

4. Air mouse calibration

4.1 Keep pressing the “OK” button to power on, and then place it on the desktop or a flat surface;

4.2 Until the LED changes from flashing to fast flashing, the static calibration is completed.

Note:

When the cursor drifts, static calibration compensation is required

5. Infrared learning operation instructions

Note:

Make sure ST works in infrared mode, and the LED light is always on at this time

1) Enter the infrared learning mode: press and hold the “TV” button for 2 to 3 seconds, the MX3 will enter the infrared learning mode, and the LED light will flash slowly every 1 second.

2) In the infrared learning mode, a TV remote control infrared head is aimed at the MX3 infrared head, press any button of the TV remote control infrared, the ST LED flashes rapidly to indicate that the code value sent by the TV remote control is captured, and the flashing interval is rapid. 200 ~ 300 ms.

3) Next, press the button corresponding to the MX3, this button will learn the code value of the TV remote control, at this time the LED flashes slowly, waiting for another button code value that needs to be learned.

4) Then, repeat steps 2) and 3) to complete the learning of other key code values.

5) Press the “TV” button for about one second to complete the infrared learning, and return to the infrared working mode, the LED light is always on.

Note:

In the infrared working mode, press and hold the “TV” button for about one second, the remote control will switch to the RF working mode, and the LED will be off at this time.

6. Voice

After the battery is turned on, the default voice is turned off, short press to turn on the voice, and then short press to turn off the voice

ST power consumption description

1. General mode

Turn on voice and somatosensory control, power consumption is less than 50mW.

2. Standby mode

If is not used for 30 seconds, the ST will enter the standby mode, at which time the power consumption is less than 25 mW.

At this point, the customer presses any key to wake up the ST.

3. Sleep mode

If is not used for 60 seconds, will enter deep sleep mode, and the power consumption is less than 0.1 mW.