ماژول کنترل دشارژ باتری مدل XH-M609

XH-M609 DC7-80V Voltage Protection Module
0
از 0 رای

0دیدگاه

برچسب: ,
  1. ولتاژ باتری قابل اتصال: 7 تا 80 ولت دی سی
  2. توان مصرفی خود ماژول:1.5 وات
  3. ابعاد:57 در 42 در 19 میلی متر
  4. دقت: 0.1 ولت دی سی
  5. مناسب برای انواع باتری ها اسیدی و لیتیومی و پلیمری
  6. دارای رله 5 ولت برای سوئیچ
نمایش بیشتر- بستن
گارانتی 48 ساعته برای ریموت کنترل ها
ضمانت اصالت کالا

7 عدد در انبار

  • ارسال توسط ای سی تک
1,048,000 ریال
مرا اگاه کن


از طریق:
ثبت

محصولات مرتبط

نقد و بررسی

ماژول کنترل دشارژ باتری مدل XH-M609
  1. ولتاژ باتری قابل اتصال: 7 تا 80 ولت دی سی
  2. توان مصرفی خود ماژول:1.5 وات
  3. ابعاد:57 در 42 در 19 میلی متر
  4. دقت: 0.1 ولت دی سی
  5. مناسب برای انواع باتری ها اسیدی و لیتیومی و پلیمری
  6. دارای رله 5 ولت برای سوئیچ
نمایش بیشتر - بستن

ماژول کنترل دشارژ باتری مدل XH-M609

از ماژول کنترل دشارژ باتری لیتیومی با ولتاژ 7 تا 80 ولت دی سی برای نظارت و مانیتورینگ ولتاژ و جریان تخلیه و کنترل خرابی باتری استفاده می شود.

شاید در نظر اول بپرسید چرا باید دشارژ شدن یک باتری را کنترل کرد؟جواب این سوال در این است که اگر باتری در وضعیت دشارژ کامل قرار بگیرد و تا مرحله غیر مجاز تخلیه پیش رود سبب به خواب رفتن و آسیب جدی و در نهایت خرابی باتری می شود.

"</div

این ماژول با کنترل تخلیه باتری تا مرز مورد نظر،که توسط کلید های کنترلی و نمایشگر تنظیم می شود،سبب عدم خاموشی باتری و در نهایت عدم
خرابی باتری می شود.

"</div

این ماژول برای باتری های 7 تا 80 ولت دی سی مناسب بوده که با دقت 0.1 ولت می توان بازه و مرز دلخواه را تنظیم کرد.توان مصرفی این ماژول به حدی کم می باشد که به هیچ عنوان سبب نگرانی نبوده و با خیال راحت می توان از آن استفاده کرد.

مشخصات فنی ماژول کنترل دشارژ باتری مدل XH-M609:

  1. ولتاژ باتری قابل اتصال: 7 تا 80 ولت دی سی
  2. توان مصرفی خود ماژول:1.5 وات
  3. ابعاد:57 در 42 در 19 میلی متر
  4. وزن:28 گرم
  5. دقت: 0.1 ولت دی سی
  6. مناسب برای انواع باتری ها اسیدی و لیتیومی و پلیمری
  7. دارای دکمه های کنترلی
  8. دارای نمایشگر سون سگمنت 7seg
  9. دارای رله 5 ولت برای سوئیچ

"</div

XH-M609 DC7-80V Voltage Protection Module Lithium Battery Under voltage Low Power Disconnect Output Board

Parameter:

Product name: Battery over-discharge protection module
Product model: HCW-M635 or XH-M609
Power supply voltage: DC7-80V
Output voltage: equal to the supply voltage
Control accuracy: 0.1V
Power consumption: <1.5W
Use range: various storage batteries / lithium batteries
Net weight: 28g
Product size: 57 x 42 x 19mm

Set to stop below 12.5 V and start above 14 V:

Set the protection value:
press “+ 一次 once to display the protection value, double-click” + 〃 “, the decimal point flashes, and then press” +,-“to change the value to 12.5. After no operation for 3 seconds, the module will automatically save and exit the setting mode.

Set the hysteresis value:

press “-〃 once to display the hysteresis value, double-click” -〃, the decimal point will flash, and press “+,-” to change the value to 1.5. After no operation for 3 seconds, the module will automatically save and exit the setting mode.

Set to stop below 10 V and start above 15.5 V:

Set the protection value: press “+ 一次 once to display the protection value, double-click” + 〃 “, the decimal point flashes, and then press” +,-“to change the value to 12.5. After no operation for 3 seconds, the module will automatically save and exit the setting mode.
Set the hysteresis value: press “-〃 once to display the hysteresis value, double-click” -〃, the decimal point will flash, and press “+,-” to change the value to 1.5. After no operation for 3 seconds, the module will automatically save and exit the setting mode.

Reset:

When the power is off, press and hold both buttons at the same time, and then power on. At this time, “888” is displayed on the screen to indicate that the factory reset is successful.
Factory set protection value: 12V, return difference: 2V

Scope of application:

Suitable for all electric two-wheel tricycle batteries in the applicable voltage range;
Car battery and new energy electric vehicle battery discharge protection;
Over-discharge protection of various batteries;
Solar, wind and other power supply systems.

Instructions:

When the new battery is used for the first time, the rated voltage value is close to the actual value, and the stop discharge voltage can be judged.
A reasonable discharge voltage value can be obtained according to the normal voltage calculation method of the battery.
When the old battery is used, the actual voltage value and the rated voltage value are quite different.
You need to measure the termination voltage value in actual use yourself.
Slow charging is usually used for battery charging (in the case of fast charging, the voltage and current are relatively large, but the
battery is easily damaged.)
The slow charging voltage is 1.2 times the rated voltage, and the charging current is adjusted to about 2/10 of the rated capacity current of the battery.
For example, the charging voltage of a 6V50Ah battery is about 7.2 volts, and the charging current is adjusted to 10A.
Reference formula: charging voltage = rated voltage X1.2, charging current = rated current X0.2

 

Package includes:

1 x XH-M609 Battery over-discharge protection module

ماژول های مشابه:

امتیاز کاربران به:

ماژول کنترل دشارژ باتری مدل XH-M609 (0نفر)
کیفیت ساخت
0
ارزش خرید به نسبت قیمت
0
امکانات و قابلیت ها
0
سهولت استفاده
0
دیدگاه خود را در باره این کالا بیان کنید برای ثبت نظر، لازم است ابتدا وارد حساب کاربری خود شوید. اگر این محصول را قبلا از این فروشگاه خریده باشید، نظر شما به عنوان مالک محصول ثبت خواهد شد. افزودن دیدگاه
نظرات کاربران

هنوز بررسی‌ای ثبت نشده است.