ماژول شارژ و دشارژ باتری های لیتیومی با نمایشگر CKCS 5V 2.4A
ماژولی تمام عیار برای شارژ و شارژ باتری های لیتیومی با ورودی تایپ سی و خروجی یو اس بی هم چنین نمایشگر ال ای دی برای نشان دادن درصد شارژ و دشارژ باقی مانده و همچنین یک کلید اکسترنال برای روشن کردن نمایشگر و خاموش کردن آن به همراه خروجی 5 ولت برای شارژ موبایل و سایر موارد از این دست.
ماژول کنترل شارژ و دشارژ باتری لیتیومی تک سل با نشانگر درصد شارژ MH-CD42
ولتاژ ورودی این ماژول برای شارژ از 5 ولت تا 5.5 ولت دی سی بوده و ولتاژقطع باتری بسته به انتخاب بین 4.2 و 4.35 ولت دی سی می باشد.
جریان خروجی این ماژول 2.4 آمپر بوده که دارای 5 درصد تلورانس می باشد.راندمان کاری این ماژول 92.5 درصد بوده که عددی بسیار مناسب برای ماژول های شارژ و دشارژ می باشد.جریان ورودی ماژول در حالت پایدار شارژ برابر 30 میکرو آمپر بوده که نگرانی از بابت دشارژ و جریان مصرفی غیر مجاز را از بین برده است.
ماژول پاوربانک فست با نمایشگر QC 5V 2.4A مدل H961-U(AN-1000)
بر روی این ماژول قابلیت اتصال انواع باتری های لیتومی و غیره ولی از نوع ولتاژ 3.6 و 3.7 ولت اماکن پذیر می باشد.
ویژگی های ماژول شارژ و دشارژ باتری های لیتیومی با نمایشگر CKCS 5V 2.4A:
- مناسب برای انواع باتری های لیتومی و موارد مشابه
- ولتاژ ورودی:5 تا 5.5 ولت دی سی
- ولتاژ شارژ باتری:4.2 و 4.35 ولت
- جریان خروجی:2.4 آمپر
- وزن:5 گرم
- ابعاد:9 در 6 در 2 سانتی متر
- راندمان کاری:92.5 درصد
- ولتاژ شروع به شارژ:از 3.2 تا 3.7 ولت
در صورتی که باتری به خواب رفته باشد با جریان 180 میلی آمپری شروع به بیدار کردن باتری می کند.
جدول راندمان کاری ماژول:
The basic parameters
Input voltage range: 5 ~ 5.5V Charge cut-off voltage: (4.2v / 4.35v) ± 0.5%
Charge current: 2.4A ± 5%
Impulse output voltage : 5V ~ 5.15v (line loss compensation)
Impulse output voltage: 100mV
Current output power: 2A
Impulse conversion efficiency: 92.5% (3.6V input, 5v2a output)
Static current at the end of the battery: <30uA Input
Package size: 9*6*2cm / 3.54*2.36*0.78in
Package weight: 5g / 0.17o
راهنمای اتصال ماژول CKCS:
function:
When the charging current is less than 50mA continuously, the output will turn off. It is compatible with the external key, which is connected
to the K point and the output negative pole. Short press to turn on the power display and turn on the 5V output. Two short strokes sucked will
turn off the power display and turn off the 5V output. When the charge current drops to 100mA after reaching the final floating charge voltage,
the charge cycle will end automatically. When the battery voltage drops below 4.1 V, the charging cycle begins again. When the battery voltage
is less than 2.8V, the battery will be pre-charged with a current of 180mA.The usb base solder position is provided on the back of the product,
which can be installed manually. It supports downloading while charging. Description of charging voltage switching As shown in the figure
below, the voltage can be changed by adjusting the solder joint of the pad. Be sure to turn off the operation!
ابعاد کلی ماژول CKCS:
3.580V input voltage, 3.086 input current, 5.112 input voltage, 2A output current, 92.50% conversion efficiency
Please cut off power and then adjust charging voltage.
Due to manual measurement, there may be deviation, please in kind prevail.
Due to lighting or other reasons, the picture and material object may slightly differ.
1 * USB-A Female Socket
- Type-C input with female, fits almost all rechargeable lithium battery.
- 5V 2A charging board module, can be very convenient to DIY.
- In load current <50mA, output shuts; after current reaches final voltage(≤100mA), cycle auto stops.
- When battery voltage drops(<4.1V), the cycle starts again; in battery voltage <2.8V, battery will be pre-charged at 180mA.
- It supports simultaneous & discharge, external connection of keys(by K point and output neg
ماژول کنترل شارژ باتری دیجیتال با نمایشگر 6 الی 60 ولت مدل XY-L30A
نقد و بررسیها3