ماژول ترموستات دیجیتال XY-T01 ModuleXY-T01 Digital Thermostat Heating Refrigeration Digital temperature control Module

XY-T01 Digital Thermostat Heating Refrigeration Digital temperature control switch temperature controller module

Product features

the electronic thermostat power supply is DC 6-30 V or 5V micro-USB, the control load current is 10A (max), the test temperature is from -50 to 110 Celsius, the temperature control accuracy is 0.1 Celsius, the refresh rate is 0.5 seconds, and the sensor length is 0.5 meters

Product function

this digital temperature control module has heating mode (“H”) and cooling mode (“C”), with the function of high temperature alarm (“ALA”), delayed start (“OPH”), temperature correction function -10.0~10.0Celsius (“OFE” ), remote parameter reading/setting, real-time temperature report and more

Working modes

this electronic temperature controller has 2 working modes, heating mode (start temperature is lower than stop temperature) and cooling mode (start temperature is higher than stop temperature), range from -50 Celsius to 110 Celsius; The high temperature control accuracy reaches 0.1 Celsius

Waterproof probe

XY-T01 electronic thermostat is equipped with a 0.5-meter NTC10K probe, which is made of stainless steel, is waterproof and not easy to rust, easy to use and can last for a long time

Use for

the electronic thermostat can be widely applied in intelligent home and industrial equipment, suitable for household appliances, office machines, audio, automobiles, etc.

Working mode/setting temperature/return temperature setting

1. In the running interface, short press the “set” key to enter the quick setting interface

2. After entering the quick setting interface, short press the “set” key to switch the parameters you want to set (work mode/set temperature/return temperature)

3. Use the “up” “down” key to modify the parameter value, and they support short press/long press

4. Press and hold the “set” button for more than 3 seconds or without any button operation for 6 seconds , it will save the parameters and automatically exit the quick setting interface.
Set ALA/OPH/OFE (alarm temperature /delay starting setting/temperature correction)

5. In the running interface, long press “set” for more than 3 seconds to enter the parameter setting interface;
Product model: XY-T01

Power supply: DC6.0-30v or 5v micro-USB

Measuring input: NTC10K/B3950

Output type: relay output 10A

Probe type: waterproof NTC probe

High temperature alarm ALA: sound-light alarm

Delay start OPH: 0-9999 minutes

Temperature correction: -10 to 10 Celsius, actual temperature = measuring temperature + calibration value

Colour:blue

Material:Electronic component

Size:About 68 x 42mm

Probe’s length: 0.5 m

Only the above package content, other products are not included.

Set Temperature —- Set T;

Backlash Temperature—–Back T;

1. Heating Mode \’H\’:

When Temperature ≤ SetT – BackT ;Relay conduction, heating equipment begin to work;

When Temperature ≥ SetT, Relay disconnect, heating equipment stop work;

2. Refrigeration mode \’C\’:

When Temperature ≥ SetT + BackT ;Relay conduction, refrigeration equipment begin to work;

When Temperature ≤ SetT ;Relay conduction, refrigeration equipment stop work;

3. High Temperature Alarm \’ALA\’:

When Temperature ≥ Alarm Temperature, The system opens the sound and light alarm, and disconnects the relay, any key stops the sound light;

4. Delay Start ‘OPH\’:

When a normal heating or refrigeration work is done, the system starts to time T, and only after the T≥OPH, the system can carry out the next round of heating or refrigeration work;

5. Temperature Correction Function OFE(-10.0 ~ 10.0°):

The system will work for a long time and may have deviations that can be corrected by this function, Temperature = Measured + Calibration;

6. Parameter Remote Read/Set:

The parameters such as setting temperature, backlash temperature and temperature correction can be set through UART.

7. Real-time Temperature Report:

If the temperature reporting function is turned on, the product is transmitted to the terminal by the UART at 1s intervals, which facilitates data collection;

8. Relay enable (default enable):

If the relay is disable, the relay remains disconnected;

9. Restore factory Settings:

At the same time press the STOP, set key more than 3S, restore factory settings;