ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس DDigital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001

  • ولتاژ کاری:8 تا 24 ولت دی سی
  • جریان مصرفی:بسته به ولتاژ تقریبا 2 آمپر
  • توان:30 وات
  • قابل تبدیل به استریو
  • امپدانس بلندگوها:4 تا 8 اهم
  • کلاس کاری:کلاس D با تکنولوژی PWM
  • امپدانس ورودی:یک کلیو اهم
  • در صورت اتصال بلندگو 4 اهم ولتاژ در بازه ی 8 تا 16 ولت
  • در صورت اتصال بلندگو 8 اهم ولتاژ در بازه ی 8 تا 24 ولت
749,000 ریال

4 عدد در انبار

نقد و بررسی اجمالیDigital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001

ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس D

ماژولی قدرتمند با ولتاژ کاری 8 تا 24 ولت و ابعاد کدچ که قابلیت جاسازی در دستگاه های مختلف را دارا می باشد.این ماژول برای بلندگوهای 4 تا 8 اهمی مناسب بوده که در صورت استفاده از بلندگو 4 اهمی ولتاژ را از 12 ولت بیشتر نبرید.

برای خرید ماژول آمپلی فایر HIFI استریو 200 وات TPA3116 کلاس D دارای بلوتوث داخلی لطفا کلیک بفرمایید.

این ماژول به صورت پیش فرض 30 وات مونو بوده که با تغییر یک عدد مقاومت بر روی برد می توان آن را به استریو 30 ولت تبدیل کرد.این ماژول دارای محل اتصال کلید برای خاموش و روشن کردن ماژول نیز می باشد.

ویژگی های ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس D:

  • ولتاژ کاری:8 تا 24 ولت دی سی
  • جریان مصرفی:بسته به ولتاژ تقریبا 2 آمپر
  • توان:30 وات
  • قابل تبدیل به استریو
  • امپدانس بلندگوها:4 تا 8 اهم
  • کلاس کاری:کلاس D با تکنولوژی PWM
  • امپدانس ورودی:یک کلیو اهم
  • در صورت اتصال بلندگو 4 اهم ولتاژ در بازه ی 8 تا 16 ولت
  • در صورت اتصال بلندگو 8 اهم ولتاژ در بازه ی 8 تا 24 ولت

ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس D

Digital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001

Description:

DY-AP3001 is a high-power mono Bluetooth audio module. Single channel audio signal output. Built-in amplifier module therefore it can connect to loudspeaker directly. It is ideal for DIY speakers and transponders.

DY-AP3001 10W/20W/30W Mono Class D Power Amplifier Module

Features:

1>.Width work voltage range

2>.Applicable multiple type speakers

3>.Support enabled/disabled output

Name :30W audio power amplifier module

Supply Voltage :DC8-24V

Work mode: Class-D(PWM modulation)

Output mode: Mono

Input mode :Default single-ended(differential input is available )

Input impedance: 1kΩ

Output load :4-8Ω

ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس D

Output power(@1KHz)

1)30W @16 4Ω

2)20W @12 4Ω

3)10W @12 8Ω

4)15W @16 8Ω

5)25W @24 8Ω

Speaker selected (30w-300w )

1)4Ω(8-16v supply )

2)8Ω(8-24v supply )

Precautions for use:

1. Recommended power supply voltage DC 8~24V, more than 26V, the chip will burn out.

2. The power supply does not exceed 16V when connected to a 4Ω speaker, and the power supply does not exceed 24V when connected to an 8Ω speaker.

3. The supply current is recommended to be 2A or more.

4. The positive and negative poles of the power supply can not be reversed, and the reverse chip is burned.

This module is only suitable for single-supply power supply and cannot be connected to a negative power supply.

5. Ensure that the input source signal is between 0.5V and 1.5V.

6. The speaker cable should not be too long, and it should be suitable within 1 meter.

7. Pay attention to static electricity protection.

Before touching the power amplifier board, first discharge the static electricity on the hand to avoid static electricity from penetrating the

power amplifier chip.

The digital power amplifier is sensitive to static electricity.

8. It is recommended to use the rated power of the speaker at 30W or above to avoid the burning of the speaker.

7.Frequently asked questions:

1>.Speaker ‘pu~’ after power ON and then no response.

1.1>.Try to reduce the input voltage to restart.

1.2>.Check if the speaker impedance is 4ohm~8ohm.Maybe the impedance is too small.

1.3>.Check power. Make sure its input current is more than 2A.

2>.There is noise during playback.

2.1>.Change the sound source and check if the sound source has its own noise.

2.2>.Use shielded audio cable.

2.3>.Change speaker.

2.4>.Change power adapter.

3>.Module get hot and smoke.

3.1>.Speaker power is too small. Change high power speakers or reduce signal input.

نمایش ادامه مطلب
نظرات کاربرانDigital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001
اولین کسی باشید که دیدگاهی می نویسد “ماژول آمپلی فایر 30 وات مونو DY-AP3001 کلاس D”

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

نقد و بررسی‌ها0

  • جدیدترین
  • مفیدترین
  • دیدگاه خریداران

هیچ دیدگاهی برای این محصول نوشته نشده است.

پرسش و پاسخDigital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001

هیچ پرسشی یافت نشد

    برای ثبت پرسش، لازم است ابتدا وارد حساب کاربری خود شوید

    نقد و بررسیDigital Amplifier Module High Power Mono Class D 4-8ohm DC 12V 24V 8V-24V For 10W 20W 30W-300W Speaker DY-AP3001