برد مادر دریل و پیچ گوشتی های شارژی 12 ولتی
اصلی
از این ماژول برای باتری های پیچ گوشتی شارژی مدل های رونیکس،AEG،توسن،میلواکی،بوش،لیدو و سایر مدلهای مشابه سه سل 12 و 12.6 ولت استفاده می شود.
در صورت عدم موجودی این محصول از دو محصول زیر استفاده کنید:
- برد شارژ باتریهای 12 ولت عمومی
- ماژول محافظ شارژ باتری لیتیومی 3 سل 6A مناسب دریل شارژی و پیچ گوشتی شارژی
حداکثر جریان خروجی این ماژول 40 آمپر دی سی بوده که عددی بسیار عالی و قابل قبول برای جریان لحظه ای تمامی مدل های دریل و پیچ گوشتی شارژی داخل بازار می باشد.
محصولات مشابه:
- ماژول مثلثی کنترل شارژ باتری لیتیومی 3 سل 8 آمپر HX-3S-03
- ماژول بالانسر و کنترل شارژ باتری 3 سل 20 آمپر سری 12V-REV 2.0
این برد کاربرد عمومی داشته و به راحتی بر روی تمامی باتری های لیتیومی و پلیمری قابل نصب و راه اندازی هست به خصوص که سیم کشی ماژول کامل بوده و نیاز به لحیم کاری خاصی وجود ندارد.
خرید برد مشابه:
این برد که به BMS یا PCB معروف هستند برای کنترل شارژ و دشارژ باتری های لیتیومی و پلیمری و نیکلی که باید به صورت مداوم مورد نظارت باشند و هر سلول به طور مجزا شارژ شود استاده می شود.
ورودی شارژ این ماژول از 12 تا 12.6 ولت بوده که ولتاژ ایده آل 12.6 ولت دی سی می باشد زیرا که ولتاژ فول شارژ هر سلول برابر 4.2 ولت دی سی بوده که در مجموع سه سل نیازمند 12.6 ولت دی سی برای شارژ کامل آنها می باشد.
مشخصات فنی برد مادر دریل و پیچ گوشتی های شارژی 12 ولتی:
- مناسب برای تمامی پیچ گوشتی و دریل های شارژی
- قابل استفاده برای مدل های رونیکس و توسن و نمونه های چینی
- قابل استفاده برای برندهای ژاپنی نظیر ماکیتا و برندهای کره ای و آلمانی بوش و آ ا گ
- جریان خروجی 40 آمپری ماژول
- دارای آی سی کنترل کننده شارژ و دشارژ
- دارای پلاتین های با کیفیت برای اتصال کامل تر
- دارای جک شارژ ورودی اماده
- ولتاژ کاری 12 تا 12.6 ولت دی سی
- معروف به بردهای BMS یا PCB
3S 12.6V Lithium Battery Protection Board Circuit Module DC Electric Tools Power Protection Board Start 40A
- model: KXYC-3S-CM01
- size: 36 * 33. 5 * 12MM
- Upper operating current: 8A
- Upper transient current: 40A ± 5A
- Overcharge range: 4. 25 ± 0. 05V
- Over voltage range: 2. 5 ± 0. 05V
- Charging voltage: 12.6V-13V
- Since the power flow: less than 30uA
- Basic functions: protection against overcharge, over discharge, short circuit, over current protection
BMS (Battery Management System) is a battery management system that is designed to monitor the condition of batteries, control the process of charging / discharging batteries, etc.
simultaneously (18650). The features of this charge controller are: protection against short circuit (short circuit) and protection against over discharge (overcharge). Also, a feature of the module is to turn off the power supply for the batteries when the maximum capacity of at least one battery is reached.
The maximum operating current of this BMS controller is 8A, the maximum starting current can reach 40A, and the quiescent current does not exceed 30uA.
The battery charge is turned off when the voltage reaches 4.25 V, and the discharge occurs when the voltage drops to 2.5 V. All this makes it an ideal solution in choosing a power controller for a power tool.
The battery charge-discharge controller module KXYC-3S-CM01 has 4 terminals for connecting batteries:
When the maximum allowable value of the supply voltage is exceeded, the charge controller activates the “protection” mode. In order to restore the operation of the module, it is necessary to reapply voltage to the BMS board input or wait for some time until the charge controller turns off the protection automatically.
The module supply voltage range is from 12.6 to 13 V. The charge voltage can be supplied through the 5.5 x 2.1 mm connector installed on the board or through the P+ and C- terminals. The load is connected to terminals P+ and P-
نقد و بررسیها0
هیچ دیدگاهی برای این محصول نوشته نشده است.